Matt McWilliams
04a0330327
All work on first draft of capper hardware
2022-06-12 22:26:03 -04:00
Matt McWilliams
2f9201716a
All capper work. Debug firmware for testing. STL of cap as printed.
2022-06-12 13:14:43 -04:00
f7a3c52260
Silly typo: did not invoke Servo_init() and so servo was not initalizing
2022-06-10 13:19:38 -04:00
Matt McWilliams
c77201ef4e
Add new commands and identifiers for the capper, start moving into capital characters
2022-06-07 07:55:26 -04:00
Matt McWilliams
2861bc52fd
intval2 connector firmware
2021-03-19 14:09:46 -04:00
eb7e62aac7
Fixed projector function
2020-10-03 21:32:16 -04:00
65292524b1
Edit addresses the issue implied by #52 . In simple tests with improvised hardware, frame cannot complete in less than 450ms, which is half a full frame. Will add another check to proj_stop() to evaluate the time elapsed and throw an error if too high or low (+/- 20%)
2020-09-29 15:13:22 -04:00
5e481e77b0
Addressing the issue with the JKMM99 projector functionality where frames stop prematurely. Conceivably, the proj_microswitch() function is the only place that calls proj_stop() so the issue is with the logic there. It makes little sense that this function allows for 15ms frames because of the test that requires a 450ms elapsed time before it is stopped.
2020-09-29 14:00:54 -04:00
c5d7f9c91f
Re-write of the JKMM99 which replaces the relay-based camera controller with an intval-based one. This relies on the Arduino Uno in the control box to handle all of the control logic in place of an on-board Arduino Trinket Pro.
2020-09-28 23:49:57 -04:00
9502d255c7
Fixed typo in Pins() where PROJECTOR_FWD was set to LOW twice instead of PROJECTOR_BWD.
2020-09-28 23:47:36 -04:00
08c3c23da0
Firmware for new JKMM99. Deployed for testing.
2020-08-18 14:21:27 -04:00
dd1bec8394
Firmware for controlling the JK 106 projector with a 103/104-style camera
2020-08-09 20:04:26 -04:00
67d0e750c2
Mcopy camera firmware
2020-07-01 18:03:20 -04:00
ed75924e24
Filmout release 1.5.0.
2020-01-20 01:37:38 -05:00
6ec81a3429
Timing tweaks for Oxberry firmware. Successfully ran 2000 frames with these settings.
2019-12-18 13:48:33 -05:00
09da9500b5
Oxberry camera firmware.
2019-12-17 14:54:01 -05:00
mmcwilliams
7a52bc7c6e
Secondary projector and secondary camera behaviors have been added to the main process. This is not represented in the UI... yet. All renderer code is still in flux.
2019-04-04 18:49:07 -04:00
mmcwilliams
f276d5ce83
Add commands for controlling a secondary projector.
2019-03-01 20:14:20 -05:00
mmcwilliams
46ce99ec18
Add an alternate camera firmware for MONO NO AWARE's JK.
2019-03-01 18:01:45 -05:00
mmcwilliams
ac888b1fc4
Firmware first drafts for MONO NO AWARE optical printer
2019-02-28 17:50:39 -05:00
mmcwilliams
b98b831ae4
Fix projector_second component code.
2019-02-26 16:42:04 -05:00
mmcwilliams
7398f7993d
Start work on secondary projector feature
2019-02-25 18:14:29 -05:00
mmcw-dev
b6a6b8a81e
Reverse High/low for relay
2019-02-09 09:30:11 -05:00
mmcwilliams
d31d7770aa
Turn off light after delay
2019-02-08 14:29:13 -05:00
mmcwilliams
74bb33052c
Create an mcopy component for cameras that are triggered by relay, ie DSLRs and intvals.
2019-02-08 12:58:14 -05:00
mmcwilliams
95007d06a2
Install libs from intval_go_node project
2019-02-08 12:46:58 -05:00
mmcwilliams
448ad1bda4
Momentary switch delay was too long.
2018-07-03 14:25:36 -04:00
mmcwilliams
4aa44576b3
Set brightness and alternatively log the rgb
2018-02-01 14:56:09 -05:00
M McWilliams
9bbf2393b7
Adjust timings in the jkfirmware
2018-01-30 05:05:04 -05:00
mmcw-dev
e3d6144abd
Solid state relay version of the mcopy jk firmware
2018-01-22 22:05:10 -05:00
mmcwilliams
695a289bdb
Settings, intval and mcopyJK firmware work.
2018-01-17 12:24:59 -05:00
mmcwilliams
f671967c18
Improve the serial test by comparing a character type
2018-01-09 23:24:09 -05:00
mmcw-dev
c8c083054e
First version of the mcopy_jk firmware for the JK103 that is being refurbished at AgX.
2018-01-05 15:49:19 -05:00
mmcw-dev
324386096a
Projector component needs a cmd_mcopy_identifier function to tell gui app that it's an arduino.
2018-01-05 15:48:50 -05:00
mmcw-dev
2301f0aa43
Started mcopy_jk firmware, based off the old mcopyJK project. Will have to trigger relays to start events. Will also have to add previous absent feature of tracking the jk state via the internam microswitches.
2018-01-04 23:45:40 -05:00
mmcw-dev
fa10ee6785
Test device with adafruit pixie
2018-01-02 01:15:45 -05:00
mmcw-dev
ed1a0902aa
Add working projector functions to mcopy_projector_jk
2017-12-28 20:54:54 -05:00
mmcw-dev
674dc9591e
Switch pixie to neopixel code in mcopy_projector_tests
2017-12-28 20:54:19 -05:00
mmcw-dev
4ffd0a7daa
Update projector and projector_tests to use distinguishing identifiers from new expanded list.
2017-12-28 18:32:03 -05:00
mmcw-dev
3efdba9ec4
Add wiring instructions to mcopy_light_tests
2017-12-28 18:31:10 -05:00
mmcwilliams
8549a08fb7
Re-organize firmware files
2017-12-28 09:30:16 -05:00
mmcwilliams
b136b78d0e
create target firmware for arduino
2017-12-27 00:37:30 -05:00
236908993e
Update requirements
2017-02-09 09:35:07 -05:00
mmcwilliams
ed593b3b7c
Merge INTVAL 2.1 project into mcopy firmware
2016-06-09 17:21:05 -04:00
mmcwilliams
413deb421d
Enable Pixie headers for testing the pixie
2016-05-25 15:58:49 -04:00
5f2dbd77b7
Merged mcopy_camera.ino into test firmware
...
Also added optional log() function to print out time that the frame
took, in ms for profiling.
2016-05-12 23:12:00 -04:00
1a116261a6
Add identification logic to camera firmware
...
This allows the Electron client to query the each Arduino and properly
assign each serial port to their function.
2016-05-12 23:10:44 -04:00
408c0beb61
Merged functions from INTVAL into camera firmware
...
Taking functionality from here:
https://github.com/sixteenmillimeter/intval2
2016-05-12 22:59:10 -04:00
a45c8104d8
Update test and firmware files to update Pixie every sec
...
Send a signal to change the color of the light every second to prevent
them from getting “stuck” re:
https://learn.adafruit.com/pixie-3-watt-smart-chainable-led-pixels/
“You do have to send it data every 1 second at a minimum (as a
protection against the bright and hot LEDs staying 'stuck on', they
will eventually timeout if no updates are received)”
2016-05-12 22:34:38 -04:00
e6aca8c6a9
Big delay in the loop for some bad reason
2016-05-12 22:25:46 -04:00
Matt McWilliams
Matthew McWilliams
sixteenmillimeter
mmcwilliams
Matt