1190 lines
39 KiB
OpenSCAD
1190 lines
39 KiB
OpenSCAD
|
|
//include <./lamp.scad>;
|
|
//include <./box_laser.scad>;
|
|
include <./common/common.scad>;
|
|
include <./common/motors.scad>;
|
|
include <./common/2020_tslot.scad>;
|
|
include <./takeup/takeup.scad>;
|
|
include <./sprocketed_roller/sprocketed_roller_var.scad>;
|
|
|
|
IN = 25.4;
|
|
|
|
16mmFilmStandard = 10.26;
|
|
16mmFilmFull = 16;
|
|
|
|
FrameX = 300;
|
|
FrameY = 175;
|
|
FrameZ = -16;
|
|
|
|
Sprockets = 18;
|
|
SprocketedRollerBevel = false;
|
|
SprocketedRollerModel = "gearbox_motor";
|
|
SprocketedRollerSetScrewTop = true;
|
|
SprocketedRollerSetScrewSide = true;
|
|
SprocketedRollerBolts = true;
|
|
|
|
DaylightW = 92;
|
|
DaylightH = 18;
|
|
|
|
PanelX = 130;
|
|
PanelY = 100;
|
|
PanelZ = 5;
|
|
PanelYOffset = 10;
|
|
PanelDimensions = [PanelX, PanelY, PanelZ];
|
|
|
|
MotorZ = -16;
|
|
TakeupMotorZ = -26;
|
|
|
|
RollerY = -20;
|
|
|
|
LampY = 20;
|
|
|
|
LampBoltX = 55;
|
|
LampBoltY = 30;
|
|
LampBoltH = 30;
|
|
|
|
LampWireX = 25;
|
|
LampWireY = 20;
|
|
|
|
LampGateX = 11;
|
|
|
|
IdleRollerPrintX = 55;
|
|
IdleRollerPrintY = 5;
|
|
IdleRollerNegativeX = 35;
|
|
IdleRollerNegativeY = -10;
|
|
|
|
IdleRollerBoltH = 30;
|
|
|
|
PictureTakeupMotorRotationZ = -70;
|
|
StockTakeupMotorRotationZ = 180-70;
|
|
|
|
ReelX = 100;
|
|
ReelY = 50;
|
|
|
|
echo("Frame 2020 X (x2)", FrameX + 20);
|
|
echo("Frame 2020 Y (x4)", FrameY);
|
|
|
|
/*
|
|
AT = 25.4 * 0.22;
|
|
|
|
|
|
INNER_BOX_X = 225;
|
|
INNER_BOX_Y = 400;
|
|
INNER_BOX_Z = 40;
|
|
|
|
OUTER_BOX_X = INNER_BOX_X + (25.4 / 2) + .2;
|
|
OUTER_BOX_Y = INNER_BOX_Y + (25.4 / 2) + .2;
|
|
OUTER_BOX_Z = 70;
|
|
|
|
REEL_SPACING = 250;
|
|
REEL_SPACING_X = 115;
|
|
|
|
REEL_HOLDER_Z = 4;
|
|
|
|
IDLE_SPACING = 120;
|
|
IDLE_OFFSET = 0;
|
|
IDLE_PLAY = 20;
|
|
IDLE_PLAY_ANGLE = 45;
|
|
IDLE_PLAY_SLOT = 8.1;
|
|
|
|
SPROCKETED_SPACING = 45;
|
|
SPROCKETED_OFFSET = 40;
|
|
SPROCKETED_Z = 7.5;
|
|
|
|
LAMP_Z = -3;
|
|
|
|
SLIT = 1;
|
|
|
|
BOLT_R = 2.55; //M5 25mm 0.8
|
|
BOLT_Z = 25;
|
|
|
|
INVOLUTE_SCALE = 1.45;
|
|
INVOLUTE_ROTATE = (360 / 12);
|
|
|
|
PEG_INNER_D = 4;
|
|
PEG_OUTER_D = 7;
|
|
PEG_H = 10;
|
|
|
|
PRESSURE_PEG_SPACING = 60;
|
|
PRESURE_PEG_OFFSET = -25;
|
|
|
|
BREAK_PEG_SPACING = 190;
|
|
BREAK_PEG_OFFSET = -80;
|
|
|
|
module m5_25 () {
|
|
cylinder(r = BOLT_R, h = BOLT_Z, center = true);
|
|
}
|
|
|
|
module roller (DEBUG = false) {
|
|
$fn = 100;
|
|
H = 21;
|
|
echo("ROLLER_CLEARANCE");
|
|
echo(H - 4);
|
|
//translate([0, 0, 9]) cube([16, 16, 20], center = true);
|
|
difference () {
|
|
union () {
|
|
cylinder(r = 24 / 2, h = 2, center = true);
|
|
translate([0, 0, 1]) cylinder(r = 16 / 2, h = 4, center = true);
|
|
translate([0, 0, 10]) cylinder(r = 14 / 2, h = 18, center = true);
|
|
translate([0, 0, H - 3.5]) cylinder(r = 16 / 2, h = 4, center = true);
|
|
translate([0, 0, H - 2]) cylinder(r = 24 / 2, h = 2, center = true);
|
|
}
|
|
cylinder(r = (IDLE_PLAY_SLOT / 2) + .1, h = 50, center = true);
|
|
if (DEBUG){
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
//translate([0, 0, H/2 - 1]) cube([25, 25, H], center = true);
|
|
}
|
|
|
|
module idle_roller_peg () {
|
|
translate([0, 0, -.6]) cylinder(r = (IDLE_PLAY_SLOT / 2) - .1, h = 39.25, center = true);
|
|
translate([0, 0, -6.75]) cylinder(r = 16 / 2, h = 2.4, center = true);
|
|
}
|
|
|
|
module idle_roller_peg_top (DEBUG = false) {
|
|
difference() {
|
|
union () {
|
|
cylinder(r = (IDLE_PLAY_SLOT / 2) + 2, h = PEG_H, center = true);//inner peg
|
|
translate([0, 0, PEG_H / 2 - 1]) cylinder(r = (IDLE_PLAY_SLOT / 2) + 4, h = 2, center = true);
|
|
translate([0, 0, -PEG_H / 2 - 1]) cylinder(r = (IDLE_PLAY_SLOT / 2) + 4, h = 2, center = true);
|
|
}
|
|
translate([0, 0, (25.4 / 4)]) cylinder(r = (IDLE_PLAY_SLOT / 2), h = 15.5 , center = true);
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module idle_roller_peg_cap (DEBUG = false) {
|
|
difference() {
|
|
union () {
|
|
cylinder(r = (IDLE_PLAY_SLOT / 2) + 2, h = 5.5, center = true);//inner peg
|
|
translate([0, 0, -1.75]) cylinder(r = (IDLE_PLAY_SLOT / 2) + 4, h = 2, center = true);
|
|
}
|
|
translate([0, 0, -7.1 - .2]) cylinder(r = (IDLE_PLAY_SLOT / 2), h = 15.5 , center = true);
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module sprocketed_roller_peg () {
|
|
D = 4.7;
|
|
cylinder(r = (D / 2) - .1, h = 30, center = true);
|
|
translate([0, 0, -2.75]) cylinder(r = 16 / 2, h = 3, center = true);
|
|
translate([0, 0, -9.25]) cylinder(r = 6 / 2, h = 11.5, center = true);
|
|
}
|
|
|
|
module sprocketed_roller_peg_cap (DEBUG = false) {
|
|
D = 4.7;
|
|
difference() {
|
|
translate([0, 0, 1.3]) cylinder(r = 5.92 - .1, h = 6, center = true);
|
|
cylinder(r = (D / 2) - .1, h = 6, center = true);
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module reel_holder (top = true) {
|
|
$fn = 60;
|
|
SQUARE_INNER = 8;
|
|
difference(){
|
|
translate([0, 0, -1.5]) cube([SQUARE_INNER, SQUARE_INNER, 21.5], center= true);
|
|
for (i = [0:4]) {
|
|
rotate([0, 0, (i * 90)]){
|
|
translate([(SQUARE_INNER / 2) + .4, (SQUARE_INNER / 2) + .4, 18.5 / 2]) rotate([0, -15, 45]) cube([2.5, SQUARE_INNER, SQUARE_INNER], center = true);
|
|
}
|
|
}
|
|
}
|
|
difference () {
|
|
union() {
|
|
translate([0, 0, (18.5 / 2) + (3.5 / 2)]) cylinder(r = SQUARE_INNER / 2, h = 3.5, center = true);
|
|
translate([0, 0, (18.5 / 2) + (7.5 / 2)]) sphere(SQUARE_INNER / 2, center = true);
|
|
}
|
|
translate ([0, 0, (18.5 / 2) + 7.5]) cube([10, 10, 2], center = true);
|
|
}
|
|
difference () {
|
|
translate([0, 0, -(18.5/ 2) - (3 / 2) - 3]) cylinder(r = 16 /2, h = 3, center = true);
|
|
//translate([0, 0, -14.3]) cube([4, 4, 2], center = true); //notch
|
|
difference() {
|
|
translate([0, 0, -14.3]) cylinder(r = 8 / 2, h = 2, center = true);
|
|
translate([0, 6, -14.3]) cube([8, 8, 2], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module bearing_laser (x, y, z, width= 8, hole = true) {
|
|
innerD = 8.05;
|
|
outerD = 22.1 - .5;
|
|
fuzz = 0.1;
|
|
translate ([x, y, z]) {
|
|
difference () {
|
|
cylinder(r = outerD / 2 + fuzz, h = width, center = true);
|
|
if (hole) {
|
|
cylinder(r = innerD / 2 - fuzz, h = width, center = true);
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
module inner_box (DUMMY = false) {
|
|
difference () {
|
|
//8.8 inches x 15 inches
|
|
if (DUMMY) {
|
|
color("lightblue") cube([INNER_BOX_X, INNER_BOX_Y, 6], center = true);
|
|
} else {
|
|
translate([0, -209.5, 0]) Box2D([INNER_BOX_X, INNER_BOX_Y, INNER_BOX_Z], SIDE_TABS = 1, TOP_TABS = 0, TOP = false, BOTTOM_TABS = 3, MATERIAL = 6);
|
|
//translate([INNER_BOX_X + 4, 14, 0]) cube([INNER_BOX_X, INNER_BOX_Y, INNER_BOX_Z], center = true);
|
|
}
|
|
idle_play_voids();
|
|
bearing_voids();
|
|
sprocketed_voids();
|
|
elastic_peg_voids();
|
|
//takeup motor mount point
|
|
translate([0, 157 + 1.25, 0]) {
|
|
cylinder(r = 6, h = 100, center = true);
|
|
//bolts
|
|
translate([(15.2 / 2), 19.14 + 1, 0]) cylinder(r = (3.75 / 2), h = 100, center = true);
|
|
translate([-(15.2 / 2), 19.14 +1, 0]) cylinder(r = (3.75 / 2), h = 100, center = true);
|
|
}
|
|
//drive motor mount point
|
|
translate([5, 0, 14.5]) rotate([0, 0, 90]) {
|
|
cylinder(r = 6, h = 100, center = true);
|
|
translate([(15.2 / 2), 19.14 + 1, 0]) cylinder(r = (3.75 / 2), h = 100, center = true);
|
|
translate([-(15.2 / 2), 19.14 +1, 0]) cylinder(r = (3.75 / 2), h = 100, center = true);
|
|
}
|
|
|
|
//light mount points, 40mm spread
|
|
translate([75, 20, 0]) cylinder(r = 3, h = 7, center = true);
|
|
translate([75, -20, 0])cylinder(r = 3, h = 7, center = true);
|
|
|
|
//Hole for light strip
|
|
translate([87, 0, 0]) cylinder(r = 5, h = 50, center = true);
|
|
|
|
//Hole for power cable to motor
|
|
translate([-10, 195, 0]) cylinder(r = 2, h = 50, center = true);
|
|
|
|
CENTER_ELEC = 546;
|
|
//Arduino USB B plug hole
|
|
translate([CENTER_ELEC, -205, 0]) cube([11.5, 11.5, 20], center = true);
|
|
|
|
//DC power
|
|
translate([CENTER_ELEC + 30, -205, 0]) cylinder(r = (11.5 / 2), h = 20, center = true);
|
|
}
|
|
}
|
|
|
|
module outer_box (DUMMY = false) {
|
|
difference () {
|
|
if (DUMMY) {
|
|
cube([OUTER_BOX_X, OUTER_BOX_Y, OUTER_BOX_Z], center = true);
|
|
} else {
|
|
translate([0, -209.5, 0]) Box2D([OUTER_BOX_X, OUTER_BOX_Y, OUTER_BOX_Z], SIDE_TABS = 1, TOP_TABS = 0, TOP = false, BOTTOM_TABS = 3, MATERIAL = 6);
|
|
}
|
|
CENTER_ELEC = 571;
|
|
//Arduino USB B plug hole
|
|
translate([CENTER_ELEC, -205, 0]) cube([11.5, 11.5, 20], center = true);
|
|
|
|
//DC power
|
|
translate([CENTER_ELEC + 30, -205, 0]) cylinder(r = (11.5 / 2), h = 20, center = true);
|
|
}
|
|
}
|
|
|
|
module light_source () {
|
|
//light mount points, 40mm spread
|
|
translate([0, 20, 0]) cylinder(r = 3, h = 7, center = true);
|
|
translate([0, -20, 0])cylinder(r = 3, h = 7, center = true);
|
|
|
|
translate ([10, 0, (7 / 2) + (3 / 2)]) {
|
|
rounded_cube([55, 80, 3], d = 20, center = true);
|
|
translate ([0, 0, 0]) {
|
|
cube([55 / 2, 80, 3], d = 20, center = true);
|
|
}
|
|
}
|
|
|
|
}
|
|
|
|
module idle_play_voids () {
|
|
translate([IDLE_OFFSET, IDLE_SPACING / 2, 0]) {
|
|
rotate([0, 0, IDLE_PLAY_ANGLE]) {
|
|
cube([IDLE_PLAY, IDLE_PLAY_SLOT, 50], center = true);
|
|
translate([IDLE_PLAY / 2, 0, 0]) cylinder(r = IDLE_PLAY_SLOT / 2, h = 50, center = true);
|
|
translate([-IDLE_PLAY / 2, 0, 0]) cylinder(r = IDLE_PLAY_SLOT / 2, h = 50, center = true);
|
|
}
|
|
}
|
|
|
|
translate([IDLE_OFFSET, -IDLE_SPACING / 2, 0]) {
|
|
rotate([0, 0, -IDLE_PLAY_ANGLE]) {
|
|
cube([IDLE_PLAY, IDLE_PLAY_SLOT, 50], center = true);
|
|
translate([IDLE_PLAY / 2, 0, 0]) cylinder(r = IDLE_PLAY_SLOT / 2, h = 50, center = true);
|
|
translate([-IDLE_PLAY / 2, 0, 0]) cylinder(r = IDLE_PLAY_SLOT / 2, h = 50, center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module bearing_voids () {
|
|
bearing_laser(REEL_SPACING_X / 2, REEL_SPACING / 2, 0, hole = false);
|
|
bearing_laser(REEL_SPACING_X / 2, -REEL_SPACING / 2, 0, hole = false);
|
|
|
|
bearing_laser(-REEL_SPACING_X / 2, REEL_SPACING / 2, 0, hole = false);
|
|
bearing_laser(-REEL_SPACING_X / 2, -REEL_SPACING / 2, 0, hole = false);
|
|
}
|
|
|
|
module sprocketed_voids () {
|
|
//translate([SPROCKETED_OFFSET, -SPROCKETED_SPACING / 2, 0]) {
|
|
//cylinder(r = 6 / 2, h = 50, center = true);
|
|
//}
|
|
//translate([SPROCKETED_OFFSET, SPROCKETED_SPACING / 2, 0]) {
|
|
//cylinder(r = 6 / 2, h = 50, center = true);
|
|
//}
|
|
bearing_laser(SPROCKETED_OFFSET, SPROCKETED_SPACING / 2, 0, hole=false);
|
|
bearing_laser(SPROCKETED_OFFSET, -SPROCKETED_SPACING / 2, 0, hole=false);
|
|
}
|
|
|
|
module bearing_hobbled_rod () {
|
|
RH_CONNECT_R = 4; //inside of bearing
|
|
difference () {
|
|
cylinder(r = RH_CONNECT_R, h = 30, center = true);
|
|
translate([RH_CONNECT_R + 2, 0, 0]) cube([RH_CONNECT_R * 2, RH_CONNECT_R * 2, 31], center = true);
|
|
}
|
|
}
|
|
|
|
module motor_hobbled_rod (h = 11) {
|
|
difference () {
|
|
translate([0, 0, 0]) cylinder(r = 5.9 / 2, h = h, center = true, $fn = 24);
|
|
translate([5.3, 0, 0]) cube([6, 6, h + .1], center = true);
|
|
}
|
|
}
|
|
|
|
module motor_15RPM (DEBUG = false) {
|
|
H = 52;
|
|
ROD = 16;
|
|
difference () {
|
|
union(){
|
|
cylinder(r = 37 / 2, h = H, center = true);
|
|
translate([0, -6, -(H / 2) - (6 / 2 )]) cylinder(r = 6, h = 6, center = true);
|
|
translate([0, -6, -(H / 2) - 6 - (ROD / 2)]) motor_hobbled_rod(ROD);
|
|
}
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module gears_to_cut () {
|
|
//http://hessmer.org/gears/InvoluteSpurGearBuilder.html
|
|
//settings 12 and 24 gears
|
|
//render with projection()
|
|
|
|
GEAR_2_CENTER = 57.8 + 8.6;
|
|
difference () {
|
|
scale([INVOLUTE_SCALE, INVOLUTE_SCALE, INVOLUTE_SCALE]) {
|
|
union () {
|
|
linear_extrude(height = 1) import("../dxf/InvoluteGear_1.dxf");
|
|
translate([0, 0, 0.5]) cube([20, 20, 1], center = true);
|
|
translate([GEAR_2_CENTER / INVOLUTE_SCALE, 0, 0.5]) cube([20, 20, 1], center = true);
|
|
}
|
|
}
|
|
bearing_hobbled_rod();
|
|
translate([GEAR_2_CENTER, 0, 0]) {
|
|
//bearing_hobbled_rod();
|
|
motor_hobbled_rod();
|
|
}
|
|
}
|
|
//find gear 2 center
|
|
//translate([GEAR_2_CENTER, 0, 0])cylinder(r = 3, h = 30, center = true);
|
|
}
|
|
|
|
module gears_to_cut_2 () {
|
|
//http://hessmer.org/gears/InvoluteSpurGearBuilder.html
|
|
//settings 20 and 12 gears
|
|
//render with projection()
|
|
|
|
GEAR_2_CENTER = 40.75;
|
|
ORIENTATION = 0;
|
|
difference () {
|
|
union () {
|
|
linear_extrude(height = 1) import("../dxf/InvoluteGear_2.dxf");
|
|
}
|
|
motor_hobbled_rod();
|
|
translate([GEAR_2_CENTER, 0, 30]) {
|
|
rotate([180, 0, ORIENTATION]) contact_printer_roller();
|
|
}
|
|
}
|
|
//find gear 2 center
|
|
//translate([GEAR_2_CENTER, 0, 0])cylinder(r = 1/2, h = 30, center = true);
|
|
}
|
|
|
|
module drive_gear_cap () {
|
|
difference () {
|
|
union () {
|
|
cylinder(r = 5, h = 5, center = true);
|
|
translate([0, 0, -(5 / 2) + (1.5 / 2)]) cylinder(r = 8, h = 1.5, center = true);
|
|
}
|
|
motor_hobbled_rod(11);
|
|
}
|
|
}
|
|
|
|
module temp_inner_walls () {
|
|
difference () {
|
|
cube([INNER_BOX_X, INNER_BOX_Y, INNER_BOX_Z], center = true);
|
|
cube([INNER_BOX_X - (25.4 / 2), INNER_BOX_Y - (25.4 / 2), INNER_BOX_Z + 1], center = true);
|
|
}
|
|
}
|
|
|
|
module temp_outer_walls () {
|
|
difference () {
|
|
cube([OUTER_BOX_X, OUTER_BOX_Y, OUTER_BOX_Z], center = true);
|
|
cube([OUTER_BOX_X - (25.4 / 2), OUTER_BOX_Y - (25.4 / 2), OUTER_BOX_Z + 1], center = true);
|
|
}
|
|
}
|
|
|
|
module temp_bottom () {
|
|
difference () {
|
|
cube([OUTER_BOX_X, OUTER_BOX_Y, 6], center = true);
|
|
}
|
|
}
|
|
|
|
module elastic_peg_bottom (DEBUG = false) {
|
|
difference() {
|
|
union () {
|
|
cylinder(r = PEG_INNER_D / 2, h = PEG_H, center = true);//inner peg
|
|
translate([0, 0, PEG_H / 2 - 1]) cylinder(r = PEG_OUTER_D, h = 2, center = true);
|
|
}
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module elastic_peg_top (DEBUG = false) {
|
|
difference() {
|
|
union () {
|
|
cylinder(r = PEG_OUTER_D / 2, h = PEG_H, center = true);//inner peg
|
|
translate([0, 0, PEG_H / 2 - 1]) cylinder(r = PEG_OUTER_D, h = 2, center = true);
|
|
translate([0, 0, -PEG_H / 2 - 1]) cylinder(r = (PEG_OUTER_D / 2) + 2, h = 2, center = true);
|
|
}
|
|
translate([0, 0, (25.4 / 4)]) cylinder(r = (PEG_INNER_D / 2), h = PEG_H , center = true);
|
|
if (DEBUG) {
|
|
translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module elastic_peg_voids () {
|
|
translate ([PRESURE_PEG_OFFSET, PRESSURE_PEG_SPACING / 2, 0]){
|
|
cylinder(r = (PEG_INNER_D / 2) + .1, h = 50, center = true);
|
|
}
|
|
translate ([PRESURE_PEG_OFFSET, -PRESSURE_PEG_SPACING / 2, 0]) {
|
|
cylinder(r = (PEG_INNER_D / 2) + .1, h = 50, center = true);
|
|
}
|
|
translate ([BREAK_PEG_SPACING / 2, BREAK_PEG_OFFSET, 0]){
|
|
cylinder(r = (PEG_INNER_D / 2) + .1, h = 50, center = true);
|
|
}
|
|
translate ([-BREAK_PEG_SPACING / 2, BREAK_PEG_OFFSET, 0]) {
|
|
cylinder(r = (PEG_INNER_D / 2) + .1, h = 50, center = true);
|
|
}
|
|
}
|
|
|
|
module reel_holder_bearing () {
|
|
$fn = 40;
|
|
BASE_D = 14;
|
|
//translate([0, 0, -0.9]) cube([3.9, 3.9, 1.9], center = true);
|
|
difference() {
|
|
translate([0, 0, -0.9]) cylinder(r = 8 / 2, h = 1.9, center = true);
|
|
translate([0, 6, -0.9]) cube([8, 8, 1.9], center = true);
|
|
}
|
|
translate([0, 0, -5.8]) cylinder(r = 8 / 2, h = 8, center = true);
|
|
translate([0, 0, -9.9]) cylinder(r = BASE_D / 2, h = 2, center=true);
|
|
}
|
|
|
|
module reel_holder_breaked () {
|
|
BREAK_D = 24;
|
|
BREAK_INNER_D = 20;
|
|
BREAK_VOID = 6;
|
|
reel_holder_bearing();
|
|
|
|
translate([0, 0, -11.5]) cylinder(r = BREAK_D / 2, h = 2, center = true);
|
|
translate([0, 0, -11.5 - BREAK_VOID / 2 - 1]) cylinder(r = BREAK_INNER_D / 2, h = BREAK_VOID, center = true);
|
|
translate([0, 0, -11.5 - BREAK_VOID - 2]) cylinder(r = BREAK_D / 2, h = 2, center = true);
|
|
}
|
|
|
|
module break () {
|
|
BREAK_INNER_D = 20.5;
|
|
BREAK_H = 5;
|
|
THICKNESS = 8;
|
|
difference() {
|
|
cylinder(r = (BREAK_INNER_D / 2) + THICKNESS, h = BREAK_H, center = true);
|
|
cylinder(r = BREAK_INNER_D / 2, h = BREAK_H + 1, center = true);
|
|
|
|
translate([0, 50, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
translate ([(BREAK_INNER_D / 2) + 11, 0, 0]) {
|
|
difference () {
|
|
translate([-2, 0, 0]) cylinder(r = 9, h = BREAK_H, center = true);
|
|
cylinder(r = 3, h = BREAK_H + 1, center = true);
|
|
|
|
translate([0, -50, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
translate([5, 0, 0]) cylinder(r = 2, h = BREAK_H, center = true);
|
|
}
|
|
translate ([-(BREAK_INNER_D / 2) - 11, 0, 0]) {
|
|
difference () {
|
|
translate([2, 0, 0]) cylinder(r = 9, h = BREAK_H, center = true);
|
|
cylinder(r = 3, h = BREAK_H + 1, center = true);
|
|
|
|
translate([0, -50, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
translate([-5, 0, 0]) cylinder(r = 2, h = BREAK_H, center = true);
|
|
}
|
|
}
|
|
|
|
module reel_holder_gear () {
|
|
reel_holder_bearing();
|
|
translate([0, 0, -13]) {
|
|
difference() {
|
|
translate([0, 0, -0.9]) cylinder(r = 8 / 2, h = 24.5 / 4, center = true);
|
|
translate([0, 6, -0.9]) cube([8, 8, (24.5 / 4) + 1], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module idle_roller_plate () {
|
|
//translate([0, 0, -.5]) cube([70, 70, 1], center = true);
|
|
translate([0, 0, 1]) roller();
|
|
translate([0, 30, (39.25 / 2) + .6]) idle_roller_peg();
|
|
translate([30, 30, PEG_H / 2 + 2]) idle_roller_peg_top();
|
|
translate([30, 0, 5.5 / 2]) rotate([180, 0, 0]) idle_roller_peg_cap();
|
|
}
|
|
|
|
module sprocketed_roller_plate () {
|
|
translate([0, 0, 15]) sprocketed_roller_peg();
|
|
translate([20, 0, 4.5]) rotate([180, 0, 0]) sprocketed_roller_peg_cap();
|
|
}
|
|
|
|
module plate () {
|
|
//translate([0, 0, -.5]) cube([150, 150, 1], center = true);
|
|
//pressure elastic_pegs
|
|
translate([60, 60, PEG_H / 2]) rotate([180, 0, 0]) elastic_peg_bottom();
|
|
translate([60, 45, (PEG_H / 2) + 2]) elastic_peg_top();
|
|
translate([45, 60, PEG_H / 2]) rotate([180, 0, 0]) elastic_peg_bottom();
|
|
translate([45, 45, (PEG_H / 2) + 2]) elastic_peg_top();
|
|
//break elastic_pegs
|
|
translate([30, 60, PEG_H / 2]) rotate([180, 0, 0]) elastic_peg_bottom();
|
|
translate([30, 45, (PEG_H / 2) + 2]) elastic_peg_top();
|
|
translate([15, 60, PEG_H / 2]) rotate([180, 0, 0]) elastic_peg_bottom();
|
|
translate([15, 45, (PEG_H / 2) + 2]) elastic_peg_top();
|
|
//reel holders
|
|
translate([60, 25, 15.25]) reel_holder();
|
|
translate([40, 25, 15.25]) reel_holder();
|
|
translate([20, 25, 15.25]) reel_holder();
|
|
translate([00, 25, 15.25]) reel_holder();
|
|
}
|
|
|
|
module sprocketed_roller_mold () {
|
|
//sprocketed_roller();
|
|
//translate([0, 0, 5]) cube([32, 32, 22],center=true);
|
|
//(CUBE = [100, 200, 50], MATERIAL = 3, SIDE_TABS = 1, BOTTOM = true, BOTTOM_TABS = 3, TOP = true, TOP_TABS = 4, PADDING = 4, PROJECTION = false)
|
|
Box2D([32, 32, 22], MATERIAL = 3, SIDE_TABS = 2, BOTTOM = true, BOTTOM_TABS = 2, TOP = false, PROJECTION = true);
|
|
}
|
|
|
|
module contact_printer (DEBUG = false) {
|
|
translate([0, 0, -15]) inner_box(true);
|
|
translate ([0, 15, 5 - (25.4 / 8)]) temp_inner_walls();
|
|
translate ([0, 15, -8 + (25.4 / 4) ]) temp_outer_walls();
|
|
//translate ([0, 15, -(25.4 / 4) - 12]) temp_bottom();
|
|
//projection()
|
|
//gears_to_cut();
|
|
//translate([0, 0, 20]) reel_holder();
|
|
//rotate([0, 0, 90]) bearing_hobbled_rod();
|
|
|
|
//translate([53, 0, .25]) gate();
|
|
|
|
translate ([PRESURE_PEG_OFFSET, PRESSURE_PEG_SPACING / 2, -14.25]) {
|
|
elastic_peg_bottom();
|
|
translate([0, 0, -25.4 / 4 - 2.2]) elastic_peg_top();
|
|
}
|
|
|
|
translate ([PRESURE_PEG_OFFSET, -PRESSURE_PEG_SPACING / 2, -14.25]) {
|
|
elastic_peg_bottom();
|
|
translate([0, 0, -25.4 / 4 - 2.2]) elastic_peg_top();
|
|
}
|
|
|
|
translate ([BREAK_PEG_SPACING / 2, BREAK_PEG_OFFSET, -14.25]) {
|
|
elastic_peg_bottom();
|
|
translate([0, 0, -25.4 / 4 - 2.2]) elastic_peg_top();
|
|
}
|
|
|
|
translate ([-BREAK_PEG_SPACING / 2, BREAK_PEG_OFFSET, -14.25]) {
|
|
elastic_peg_bottom();
|
|
translate([0, 0, -25.4 / 4 - 2.2]) elastic_peg_top();
|
|
}
|
|
|
|
//negative feed
|
|
translate([REEL_SPACING_X / 2, -REEL_SPACING / 2, 0]) {
|
|
translate([0, 0, 1]) daylight_spool();
|
|
translate([0, 0, REEL_HOLDER_Z]) reel_holder();
|
|
//translate([0, 0, -10]) reel_holder_breaked();
|
|
|
|
translate([0, 0, -25.5]) rotate([0, 0, -40]) break();
|
|
}
|
|
|
|
//negative takeup
|
|
translate([REEL_SPACING_X / 2, REEL_SPACING / 2, 0]) {
|
|
translate([0, 0, 1]) daylight_spool();
|
|
translate([0, 0, REEL_HOLDER_Z]) reel_holder();
|
|
translate([0, 0, -10]) reel_holder_gear();
|
|
}
|
|
|
|
//print stock feed
|
|
translate([-REEL_SPACING_X / 2, -REEL_SPACING / 2, 0]) {
|
|
translate([0, 0, 1]) daylight_spool();
|
|
if (DEBUG) {
|
|
translate([0, 0, 1]) color([1, 1, 1, .5]) cylinder(r = 150, h = 16, center = true);
|
|
}
|
|
translate([0, 0, REEL_HOLDER_Z]) reel_holder();
|
|
//translate([0, 0, -10]) reel_holder_breaked();
|
|
|
|
translate([0, 0, -25.5]) rotate([0, 0, 40]) break();
|
|
}
|
|
|
|
//print stock takeup
|
|
translate([-REEL_SPACING_X / 2, REEL_SPACING / 2, 0]) {
|
|
//translate([0, 0, 1]) daylight_spool();
|
|
translate([0, 0, REEL_HOLDER_Z]) reel_holder();
|
|
translate([0, 0, -10]) reel_holder_gear();
|
|
}
|
|
|
|
translate([IDLE_OFFSET - 7, (IDLE_SPACING / 2) - 7, -9]) {
|
|
roller();
|
|
translate([0, 0, 5]) idle_roller_peg();
|
|
translate([0, 0, -14]) idle_roller_peg_top();
|
|
translate([0, 0, 23]) idle_roller_peg_cap();
|
|
}
|
|
translate([IDLE_OFFSET, -(IDLE_SPACING / 2), -9]) {
|
|
translate([0, 0, 0.5]) roller(DEBUG);
|
|
translate([0, 0, 5]) idle_roller_peg();
|
|
translate([0, 0, -14]) idle_roller_peg_top(DEBUG);
|
|
translate([0, 0, 23.5]) idle_roller_peg_cap(DEBUG);
|
|
}
|
|
|
|
translate([SPROCKETED_OFFSET, -SPROCKETED_SPACING / 2, SPROCKETED_Z]) {
|
|
rotate([180, 0 ,0]) {
|
|
//difference () {
|
|
contact_printer_roller();
|
|
//translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
//}
|
|
}
|
|
//translate([0, 0, -15]) sprocketed_roller_peg();
|
|
//translate([0, 0, -3]) sprocketed_roller_peg_cap();
|
|
}
|
|
translate([SPROCKETED_OFFSET, SPROCKETED_SPACING / 2, SPROCKETED_Z]) {
|
|
rotate([180, 0 ,0]) contact_printer_roller();
|
|
//translate([0, 0, -15]) sprocketed_roller_peg();
|
|
//translate([0, 0, -3]) sprocketed_roller_peg_cap();
|
|
}
|
|
|
|
//find motor mount point
|
|
//translate([0, 157, 0]) cylinder(r = 3, h = 100, center = true);
|
|
//takeup motor
|
|
translate([0, 157 + 6 + 1.25, 14 + .5]) motor_15RPM();
|
|
translate([0, 0, 14.5]) rotate([0, 0, 90]) motor_15RPM();
|
|
|
|
echo("ROTATING GEARS");
|
|
echo(INVOLUTE_ROTATE);
|
|
translate([-REEL_SPACING_X / 2, REEL_SPACING / 2, -23]) rotate([0, 0, INVOLUTE_ROTATE]) gears_to_cut();
|
|
//translate([REEL_SPACING_X / 2, REEL_SPACING / 2, -23]) rotate([0, 0, 180 - INVOLUTE_ROTATE ]) gears_to_cut();
|
|
|
|
//translate([75, 0, -15]) light_source();
|
|
}
|
|
|
|
module reel_holder_plate () {
|
|
reel_holder();
|
|
translate([0, 20, 0]) reel_holder();
|
|
translate([20, 20, 0]) reel_holder();
|
|
translate([20, 0, 0]) reel_holder();
|
|
}
|
|
|
|
//corner pieces for outer box to support inner box
|
|
|
|
// ___________
|
|
// |/ \|
|
|
// | |
|
|
// |\_______/|
|
|
|
|
module spacer () {
|
|
H = 16.3;
|
|
W = 25;
|
|
difference () {
|
|
rotate([0, 0, 45]) cube([W, W, H], center = true);
|
|
translate([150, 0, 0]) cube([300, 300, 300], center = true);
|
|
}
|
|
}
|
|
|
|
module four_point_connector () {
|
|
$fn = 120;
|
|
X = 35;
|
|
Y = 40;
|
|
H = 8.5;
|
|
Z = ((H - 6) / 2) - 1;
|
|
translate([0, 0, -4.5]) {
|
|
difference () {
|
|
//plate
|
|
rounded_cube([X + 5.6 + 2, Y + 5.6 + 2, 3], d = 2.8 * 2, center = true);
|
|
//negative
|
|
rounded_cube([X - 7, Y - 7, 4], d = 20, center = true);
|
|
}
|
|
}
|
|
translate([X / 2, Y / 2, Z + 2.5]) cylinder(r = 2.8, h = H + 5, center = true);
|
|
translate([X / 2, -Y / 2, Z + 2.5]) cylinder(r = 2.8, h = H + 5, center = true);
|
|
|
|
translate([-X / 2, Y / 2, Z + .5]) cylinder(r = 2.8, h = H + 1, center = true);
|
|
translate([-X / 2, -Y / 2, Z + .5]) cylinder(r = 2.8, h = H + 1, center = true);
|
|
}
|
|
|
|
module sprocketed_roller_gear_cap () {
|
|
difference () {
|
|
union () {
|
|
cylinder(r = 16 / 2, h = 3, center = true);
|
|
translate([0, 0, 1.5]) cylinder(r = 11 / 2, h = 6, center = true);
|
|
}
|
|
translate([0, 0, -30]) contact_printer_roller();
|
|
}
|
|
}*/
|
|
|
|
|
|
|
|
//contact_printer();
|
|
/*projection() {
|
|
intersection () {
|
|
inner_box();
|
|
translate([30, 0, 0]) cube([130, 160, 50], center = true);
|
|
}
|
|
}*/
|
|
//translate([23, 0, 0]) cube([35, 45, 5], center = true);
|
|
//translate([8, 0, -26]) rotate([0, 0, 34]) import("/home/mathias/Desktop/InvoluteGear_2.dxf");
|
|
//translate([20, 0, -20]) cube([41.6, 0.5, 2], center = true);
|
|
//translate([0, 0, 6]) outer_box();
|
|
//translate([57.5, 0, 0]) four_point_connector();
|
|
//translate([40, 0, LAMP_Z]) rotate([0, 0, -90]) {
|
|
//lamp_plate();
|
|
//lamp_housing();
|
|
//translate([0, 15, 4]) lamp_front();
|
|
//gate();
|
|
|
|
//}
|
|
//sprocketed_roller_gear_cap ();
|
|
//reel_holder_plate();
|
|
//reel_holder();
|
|
//translate([60, 45, PEG_H / 2]) rotate([180, 0, 0]) elastic_peg_top();
|
|
//reel_holder_breaked();
|
|
//projection() gears_to_cut();
|
|
//projection() gears_to_cut_2();
|
|
//drive_gear_cap();
|
|
//break();
|
|
//sprocketed_roller();
|
|
//sprocketed_roller_plate();
|
|
//projection()
|
|
//translate([0, 0, 15 - 6]) inner_box(true);
|
|
//projection() outer_box();
|
|
//idle_roller_plate();
|
|
//plate();
|
|
//roller();
|
|
//light_source();
|
|
//spacer();
|
|
//contact_printer_roller();
|
|
|
|
//sprocketed_roller_mold();
|
|
|
|
/**
|
|
* DEBUG MODULES
|
|
**/
|
|
|
|
module daylight_spool (DEBUG = false) {
|
|
//inner starting d = 31.5 or 32
|
|
color([[255, 0, 0, 1]]) difference () {
|
|
cylinder(r = R(DaylightW), h = DaylightH - 0.1, center = true);
|
|
cylinder(r = R(DaylightW) + 1, h = DaylightH - 2, center = true);
|
|
cube([9, 9, 50], center=true);
|
|
translate([4.5, 4.5, 0]) {
|
|
rotate([0, 0, 45]) {
|
|
cube([3, 3, 50], center=true);
|
|
}
|
|
}
|
|
}
|
|
difference () {
|
|
cylinder(r = R(32), h = DaylightH - 0.2, center=true);
|
|
cylinder(r = R(32) - 1, h = DaylightH + 1, center=true);
|
|
translate([0, 32/2, 0]) {
|
|
cube([1.3, 10, 18], center=true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module four_hundred_foot_spool (pos = [0, 0, 0]) {
|
|
W = 175;
|
|
H = 18;
|
|
translate(pos) {
|
|
cylinder(r = R(W), h = H, center = true, $fn = 200);
|
|
}
|
|
}
|
|
|
|
module centered_geared_motor (pos = [0, 0, 0], rot = [0, 0, 0]) {
|
|
translate(pos) rotate(rot) {
|
|
translate([8.25, 0, 0]) geared_motor();
|
|
}
|
|
}
|
|
|
|
module debug () {
|
|
DaylightZ = 11.5;
|
|
PanelOffsetZ = -2.5;
|
|
//////
|
|
panel([0, 0, PanelOffsetZ]);
|
|
UseDaylight = true;
|
|
|
|
translate([0, RollerY, 18]) rotate([180, 0, 0]) difference () {
|
|
sprocketed_roller(sprockets = Sprockets, bevel = SprocketedRollerBevel, model = SprocketedRollerModel, set_screw_top = SprocketedRollerSetScrewTop, set_screw_side = SprocketedRollerSetScrewSide, bolts = SprocketedRollerBolts);
|
|
//translate([50, 0, 0]) cube([100, 100, 100], center = true);
|
|
}
|
|
//lamp
|
|
//difference () {
|
|
lamp([0, LampY, 0 + 1]);
|
|
// translate([45, LampY, 0 + 2]) cube([100, 100, 100], center = true);
|
|
//}
|
|
color("green") lamp_cover([0, LampY + 15, 21]);
|
|
color("red") lamp_bolts_voids([0, LampY + 15, (LampBoltH/2) - 1.5 - 2.5]);
|
|
//gates
|
|
translate([-5.35, LampY -7.1, 11 + 1 + .1]) rotate([0, 0, 7]) color("blue") picture_gate();
|
|
|
|
//idle rollers
|
|
idle_roller([ IdleRollerPrintX, IdleRollerPrintY, 3]);
|
|
idle_roller([-IdleRollerPrintX, IdleRollerPrintY, 3]);
|
|
idle_roller([ IdleRollerNegativeX, IdleRollerNegativeY, 3]);
|
|
idle_roller([-IdleRollerNegativeX, IdleRollerNegativeY, 3]);
|
|
//active roller
|
|
centered_geared_motor([0, RollerY, MotorZ], [180, 0, 90]);
|
|
|
|
if (UseDaylight) {
|
|
//feed
|
|
translate([-ReelX, ReelY, DaylightZ]) daylight_spool();
|
|
translate([-ReelX, -ReelY, DaylightZ]) daylight_spool();
|
|
//takeup
|
|
//translate([ReelX, ReelY, DaylightZ]) daylight_spool();
|
|
//translate([ReelX, -ReelY, DaylightZ]) daylight_spool();
|
|
} else {
|
|
four_hundred_foot_spool([-ReelX, ReelY, DaylightZ]);
|
|
four_hundred_foot_spool([-ReelX, -ReelY, DaylightZ]);
|
|
//takeup
|
|
four_hundred_foot_spool([ReelX, ReelY, DaylightZ]);
|
|
four_hundred_foot_spool([ReelX, -ReelY, DaylightZ]);
|
|
}
|
|
|
|
//takeup
|
|
takeup_panel_picture([ReelX, ReelY, PanelOffsetZ+1]);
|
|
translate([ReelX, ReelY, -10]) magnetic_coupling();
|
|
translate([ReelX, ReelY, -10]) slip_coupling();
|
|
|
|
centered_geared_motor([ReelX, ReelY, TakeupMotorZ], [180, 0, PictureTakeupMotorRotationZ]);
|
|
centered_geared_motor([ReelX, -ReelY, TakeupMotorZ], [180, 0, StockTakeupMotorRotationZ]);
|
|
|
|
//translate([0, 0, DaylightZ]) color("red", 0.25) cube([250, 100, 16], center = true);
|
|
|
|
//2020 frame
|
|
//top/bottom
|
|
translate([0, (FrameY/2) + 10, FrameZ]) rotate([0, 90, 0]) 2020_tslot(FrameX + 20);
|
|
translate([0, -(FrameY/2) - 10, FrameZ]) rotate([0, 90, 0]) 2020_tslot(FrameX + 20);
|
|
//far sides
|
|
translate([FrameX/2, 0, FrameZ]) rotate([90, 0, 0]) 2020_tslot(FrameY);
|
|
translate([-FrameX/2, 0, FrameZ]) rotate([90, 0, 0]) 2020_tslot(FrameY);
|
|
//inner rails
|
|
translate([(PanelX/2) - 10, 0, FrameZ]) rotate([90, 0, 0]) 2020_tslot(FrameY);
|
|
translate([-(PanelX/2) + 10, 0, FrameZ]) rotate([90, 0, 0]) 2020_tslot(FrameY);
|
|
}
|
|
|
|
/**
|
|
* CONTACT PRINTER MODULES
|
|
**/
|
|
|
|
module m3_panel_bolt_void (pos = [0, 0, 0], H = 10) {
|
|
translate(pos) {
|
|
cylinder(r = R(6), h = 5, center = true, $fn = 40);
|
|
translate([0, 0, -(H/2) - (5/2) + 0.01]) cylinder(r = R(3.25), h = H, center = true, $fn = 25);
|
|
}
|
|
}
|
|
|
|
module takeup_mount_panel (pos = [0, 0, 0], rot = [0, 0, 0]) {
|
|
translate(pos) rotate(rot) intersection() {
|
|
minimal_mount();
|
|
translate([10, 0, 0]) cube([50, 30, 10], center = true);
|
|
}
|
|
}
|
|
|
|
module panel_motor_mount_void (pos = [0, 0, 0]) {
|
|
H = 10;
|
|
D = 7.5 + 1.5;
|
|
translate(pos) {
|
|
cylinder(r = R(6), h = H, center = true, $fn = 40);
|
|
}
|
|
}
|
|
|
|
module idle_roller (pos = [0, 0, 0]) {
|
|
$fn = 80;
|
|
translate(pos) {
|
|
difference () {
|
|
union () {
|
|
cylinder(r = R(16), h = 1, center = true);
|
|
translate([0, 0, 17]) cylinder(r = R(16), h = 1, center = true);
|
|
translate([0, 0, 17/2]) cylinder(r = R(12), h = 17, center = true);
|
|
}
|
|
cylinder(r = R(4.5), h = 20, center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module lamp_bolt_void (pos = [0, 0, 0], H = LampBoltH) {
|
|
translate(pos) {
|
|
cylinder(r = R(4.25), h = H, center = true);
|
|
translate([0, 0, -H/2]) m4_nut();
|
|
}
|
|
}
|
|
|
|
module idle_roller_bolt_void (pos = [0, 0, 0], H = IdleRollerBoltH) {
|
|
translate(pos) {
|
|
cylinder(r = R(4.25), h = H, center = true);
|
|
translate([0, 0, -H/2]) m4_nut();
|
|
}
|
|
}
|
|
|
|
module lamp_bolts_voids (pos = [0, 0, 0], H = 10) {
|
|
X = LampBoltX/2;
|
|
Y = LampBoltY/2;
|
|
$fn = 30;
|
|
translate(pos) {
|
|
lamp_bolt_void([X, Y, 0]);
|
|
lamp_bolt_void([-X, Y, 0]);
|
|
lamp_bolt_void([X, -Y, 0]);
|
|
lamp_bolt_void([-X, -Y, 0]);
|
|
}
|
|
}
|
|
|
|
module lamp_post (pos = [0, 0, 0]) {
|
|
$fn = 40;
|
|
H = 20;
|
|
translate(pos) difference () {
|
|
cylinder(r = R(8), h = H, center = true);
|
|
cylinder(r = R(4.25), h = H + 1, center = true);
|
|
}
|
|
}
|
|
|
|
module lamp_posts (pos = [0, 0, 0], H = 10) {
|
|
X = LampBoltX/2;
|
|
Y = LampBoltY/2;
|
|
$fn = 30;
|
|
translate(pos) {
|
|
lamp_post([X, Y, 0]);
|
|
lamp_post([-X, Y, 0]);
|
|
lamp_post([X, -Y, 0]);
|
|
lamp_post([-X, -Y, 0]);
|
|
}
|
|
}
|
|
|
|
module lamp_gate_bracket (pos = [0, 0, 0], rot = [0, 0, 0]) {
|
|
X = LampGateX;
|
|
translate(pos) rotate(rot) {
|
|
difference () {
|
|
cube([X, 15, 18], center = true);
|
|
translate([0, 4, 1]) cube([X-4, 15, 18], center = true);
|
|
translate([0, -3, 1]) cube([X-7, 15, 18], center = true);
|
|
translate([0, -5.25, 0]) cube([X-4, 1.5, 18.01], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module picture_gate_bracket (pos = [0, 0, 0], rot = [0, 0, 0]) {
|
|
translate(pos) rotate(rot) difference() {
|
|
lamp_gate_bracket();
|
|
translate([0, 0, 0]) cube([4, 20, 17], center = true);
|
|
}
|
|
}
|
|
|
|
module sound_gate_bracket (pos = [0, 0, 0], rot = [0, 0, 0]) {
|
|
LedD = 5;
|
|
LedZ = -6.5;
|
|
translate(pos) rotate(rot) {
|
|
difference () {
|
|
lamp_gate_bracket();
|
|
translate([0, 2, LedZ]) rotate([0, 90, 90]) {
|
|
cylinder(r = R(LedD), h = 16, center = true, $fn = 40);
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
module gate_blank () {
|
|
X = LampGateX;
|
|
//front
|
|
translate([0, -6.25, 0]) cube([X-7.2, 1.2, 19.25], center = true);
|
|
//middle
|
|
translate([0, -5.1, -0.5]) cube([X-4.2, 1.4, 19], center = true);
|
|
|
|
//top
|
|
translate([0, -5.9, 9]) cube([X-4.2, 3, 2], center = true);
|
|
}
|
|
//standard, super, full, sound
|
|
module picture_gate (pos = [0, 0, 0], rot = [0, 0, 0], Type = "full", Width = 2) {
|
|
X = LampGateX;
|
|
translate(pos) rotate(rot) {
|
|
difference () {
|
|
union () {
|
|
gate_blank();
|
|
}
|
|
if (Type == "standard") {
|
|
translate([0, -6, -0.7]) cube([Width, 10, 16mmFilmStandard], center = true);
|
|
} else if (Type == "full") {
|
|
translate([0, -6, -1.1]) cube([Width, 10, 16mmFilmFull], center = true);
|
|
} else if (Type == "super") {
|
|
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
module lamp (pos = [0, 0, 0]) {
|
|
Z = 10;
|
|
WallZ = Z;
|
|
GateZ = Z;
|
|
PostsZ = Z - 1;
|
|
translate(pos) {
|
|
intersection () {
|
|
difference () {
|
|
rounded_cube([70, 70, 2], d = 4, center = true);
|
|
translate([0, -45, 0]) cylinder(r = R(60), h = 4 + 1, center = true, $fn = 200);
|
|
lamp_bolts_voids([0, 15, -2]);
|
|
translate([LampWireX, LampWireY, 0]) cylinder(r = R(10), h = 10, center = true);
|
|
translate([-LampWireX, LampWireY, 0]) cylinder(r = R(10), h = 10, center = true);
|
|
}
|
|
translate([0, 45, 0]) cylinder(r = R(130), h = 4 + 1, center = true, $fn = 200);
|
|
}
|
|
//walls
|
|
translate([0, 15, WallZ]) difference () {
|
|
rounded_cube([70, 40, 18], d = 4, center = true);
|
|
cube([70-6, 40-6, 18 + 1], center = true);
|
|
translate([0, -20, 0]) cube([20, 40-6, 18 + 1], center = true);
|
|
}
|
|
lamp_posts([0, 15, PostsZ]);
|
|
//sound
|
|
difference () {
|
|
union () {
|
|
sound_gate_bracket([5.35, -7, GateZ], [0, 0, -7]);
|
|
picture_gate_bracket([-5.35, -7, GateZ], [0, 0, 7]);
|
|
}
|
|
translate([0, -53.5, 11]) cylinder(r = R(80), h = 18.01, center = true, $fn = 200);
|
|
}
|
|
//barrier
|
|
translate([0, 10.6+7, 11]) cube([5.5, 34, 18], center = true);
|
|
translate([0, 5, 11]) cube([3, 20, 18], center = true);
|
|
}
|
|
}
|
|
|
|
module lamp_cover (pos = [0, 0, 0]) {
|
|
translate(pos) difference () {
|
|
union () {
|
|
rounded_cube([70, 40, 2], d = 4, center = true);
|
|
translate([5.35, -15-7, 0]) rotate([0, 0, -7]) cube([LampGateX, 15-6, 2], center = true);
|
|
translate([-5.35, -15-7, 0]) rotate([0, 0, 7]) cube([LampGateX, 15-6, 2], center = true);
|
|
translate([0, -15-7, 0])cube([4, 4, 2], center = true);
|
|
|
|
}
|
|
lamp_bolts_voids([0, 0, 0]);
|
|
}
|
|
}
|
|
|
|
module panel (pos = [0, 0, 0]) {
|
|
BoltX = (PanelX-20)/2;
|
|
BoltY2 = (PanelY)/2;
|
|
|
|
BoltY1 = 30;
|
|
|
|
MotorMountX = (GearedMotorMountX + 0.1) / 2;
|
|
MotorMountY = (GearedMotorMountY + 0.1) / 2;
|
|
|
|
LampBoltsZ = (LampBoltH/2) - 1.5;
|
|
IdleRollerBoltsZ = (IdleRollerBoltH/2) - 1.5;
|
|
|
|
SprocketedRollerZ = -5;
|
|
|
|
color("green") translate (pos) difference() {
|
|
translate([0, PanelYOffset, 0]) cube(PanelDimensions, center = true);
|
|
|
|
//sprocketed roller
|
|
translate([0, RollerY, 0]) cylinder(r = R(15), h = PanelZ + 1, center = true, $fn = 60);
|
|
translate([0, -12.5, -4 + 2.5]) rotate([0, 0, 90]) {
|
|
panel_motor_mount_void([MotorMountX, MotorMountY, 0]);
|
|
panel_motor_mount_void([-MotorMountX, MotorMountY, 0]);
|
|
panel_motor_mount_void([MotorMountX, -MotorMountY, 0]);
|
|
panel_motor_mount_void([-MotorMountX, -MotorMountY, 0]);
|
|
}
|
|
|
|
//panel bolts
|
|
m3_panel_bolt_void([BoltX, -BoltY1, 3]);
|
|
m3_panel_bolt_void([-BoltX, -BoltY1, 3]);
|
|
m3_panel_bolt_void([BoltX, BoltY1, 3]);
|
|
m3_panel_bolt_void([-BoltX, BoltY1, 3]);
|
|
m3_panel_bolt_void([BoltX, BoltY2, 3]);
|
|
m3_panel_bolt_void([-BoltX, BoltY2, 3]);
|
|
|
|
//idle roller posts
|
|
idle_roller_bolt_void([ IdleRollerPrintX, IdleRollerPrintY, IdleRollerBoltsZ]);
|
|
idle_roller_bolt_void([-IdleRollerPrintX, IdleRollerPrintY, IdleRollerBoltsZ]);
|
|
idle_roller_bolt_void([ IdleRollerNegativeX, IdleRollerNegativeY, IdleRollerBoltsZ]);
|
|
idle_roller_bolt_void([-IdleRollerNegativeX, IdleRollerNegativeY, IdleRollerBoltsZ]);
|
|
|
|
//lamp
|
|
lamp_bolts_voids([0, LampY + 15, LampBoltsZ]);
|
|
//lamp wire voids
|
|
translate([0, LampY, 0]) {
|
|
translate([LampWireX, LampWireY, 0]) cylinder(r = R(10), h = 10, center = true);
|
|
translate([-LampWireX, LampWireY, 0]) cylinder(r = R(10), h = 10, center = true);
|
|
}
|
|
|
|
}
|
|
takeup_mount_panel([0, RollerY, SprocketedRollerZ], [0, 0, 90]);
|
|
}
|
|
|
|
module takeup_panel_picture (pos = [0, 0, 0]) {
|
|
TakeupPanelX = 95;
|
|
TakeupPanelY = 90;
|
|
OtherX = 25;
|
|
OtherY = 45;
|
|
translate(pos) {
|
|
union(){
|
|
translate([12.5, 10, 0]) cube([TakeupPanelX, TakeupPanelY, PanelZ], center = true);
|
|
translate([-(TakeupPanelX/2), (TakeupPanelY/2)-12.5, 0]) cube([OtherX, OtherY, PanelZ], center = true);
|
|
}
|
|
}
|
|
}
|
|
|
|
module takeup_panel_stock (pos = [0, 0, 0]) {
|
|
translate(pos) {
|
|
|
|
}
|
|
}
|
|
|
|
PART = "";
|
|
LIBRARY = true;
|
|
|
|
if (PART == "panel") {
|
|
rotate([180, 0, 0]) panel();
|
|
} else if (PART == "lamp") {
|
|
lamp();
|
|
} else if (PART == "picture_gate") {
|
|
rotate([-90, 0, 0]) picture_gate(Type = "standard");
|
|
} else if (PART == "sprocketed_roller_reinforced") {
|
|
sprocketed_roller(sprockets = Sprockets, bevel = SprocketedRollerBevel, model = SprocketedRollerModel, set_screw_top = SprocketedRollerSetScrewTop, set_screw_side = SprocketedRollerSetScrewSide, bolts = SprocketedRollerBolts, reinforced = true);
|
|
} else if (PART == "2020_tslot_insert") {
|
|
2020_tslot_insert();
|
|
} else {
|
|
debug();
|
|
}
|