More mount work and start of endstop logic. Rebuilding the B&H projector unity.

ino/components/mcopy_capper/mcopy_capper.ino

@@ -145,15 +145,15 @@ int Servo_delay (int angleA, int angleB) {
 void Cap_off (boolean suppress, boolean force) {
   Endstop_on();
   current_angle = servo.read();
-  if ((Read_endstop() || force) && (cap_state || current_angle != cap_off_angle)) {
+  if ( (cap_state || current_angle != cap_off_angle)) {
     Servo_angle(cap_off_angle);
     cap_state = false;
   } else {
     log("Cap already off");
   }
-  while (Read_endstop()) {
+  /*while (Read_endstop()) {
     delay(1);
-  }
+  }*/
   Endstop_off();
   log("Cap_off()");
   if (!suppress) {
@@ -164,15 +164,15 @@ void Cap_off (boolean suppress, boolean force) {
 void Cap_on (boolean suppress, boolean force) {
   Endstop_on();
   current_angle = servo.read();
-  if ((!Read_endstop() || force) && (!cap_state || current_angle != cap_on_angle)) {
+  if ( (!cap_state || current_angle != cap_on_angle)) {
     Servo_angle(cap_on_angle);
     cap_state = true;
   } else {
     log("Cap already on");
   }
-  while (!Read_endstop()) {
+  /*while (!Read_endstop()) {
     delay(1);
-  }
+  }*/
   Endstop_off();
   log("Cap_on()");
   if (!suppress) {

ino/components/mcopy_projector/mcopy_projector.ino

@@ -1,13 +1,14 @@
 boolean debug_state = false;
 
-const int proj_fwd_pin = 12;
-const int proj_bwd_pin = 11;
-const int proj_pin = 10;
+const int proj_fwd_pin = 9;
+const int proj_bwd_pin = 10;
+const int proj_micro_pin = 4;
 const int proj_time = 1200;
 const int proj_delay = 42;
 
 boolean proj_dir = true; 
 boolean proj_running = false;
+volatile int proj_micro_raw;
 
 const char cmd_projector = 'p';
 const char cmd_proj_forward = 'g';
@@ -25,6 +26,16 @@ void setup() {
   Serial.begin(57600);
   Serial.flush();
   Serial.setTimeout(serialDelay);
+  pins_init();
+}
+
+void pins_init () {
+  pinMode(proj_fwd_pin, OUTPUT);
+  pinMode(proj_bwd_pin, OUTPUT);
+  pinMode(proj_micro_pin, INPUT_PULLUP);
+
+  analogWrite(proj_fwd_pin, 0);
+  analogWrite(proj_bwd_pin, 0);
 }
 
 void loop() {
@@ -36,6 +47,9 @@ void loop() {
     cmd(cmd_char);
     cmd_char = 'z';
   }
+  if (proj_running) {
+    proj_reading();
+  }
 }
 
 void cmd (char val) {
@@ -72,11 +86,11 @@ void identify () {
 
 void proj_start () {
   if (proj_dir) {
-    digitalWrite(proj_fwd_pin, HIGH);
-    digitalWrite(proj_bwd_pin, LOW); 
+    analogWrite(proj_fwd_pin, 255);
+    analogWrite(proj_bwd_pin, 0); 
   } else {
-    digitalWrite(proj_bwd_pin, HIGH); 
-    digitalWrite(proj_fwd_pin, LOW); 
+    analogWrite(proj_bwd_pin, 255); 
+    analogWrite(proj_fwd_pin, 0); 
   }
   proj_running = true;
   delay(500); // Let bump pass out of microswitch
@@ -95,8 +109,8 @@ void proj_reading () {
 }
 
 void proj_stop () {
-  digitalWrite(proj_bwd_pin, LOW); 
-  digitalWrite(proj_fwd_pin, LOW);
+  analogWrite(proj_bwd_pin, 0); 
+  analogWrite(proj_fwd_pin, 0);
   
   proj_running = false;
   

scad/capper.scad

@@ -25,7 +25,7 @@ RailSlotsD = 6;
 
 MountBoltSpacingY=40;
 
-OptoEndstopAdjustZ=2;
+OptoEndstopAdjustZ=2-9;
 
 module OptoEndstop () {
     $fn=30;
@@ -44,6 +44,7 @@ module OptoEndstop () {
         translate([0,R(Y)+R(4.15),-R(1.75)-R(10.15)]) cube([6.1, 4.15, 10.15], center=true);
         translate([0,-R(Y)-R(4.15),-R(1.75)-R(10.15)]) cube([6.1, 4.15, 10.15], center=true);
     }
+    translate([3,4, -R(1.75)-R(.75)]) cube([3.6, 15.7, .75], center=true);
 }
 
 module BoltVoid () {
@@ -85,9 +86,12 @@ module Mount () {
         translate([80, R(MountBoltSpacingY), 0]) RailSlots();
         translate([80, -R(MountBoltSpacingY), 0]) RailSlots();
         //endstop
-        translate([0, -34, 25-2-2]) {
-            cube([14, 20, 50], center=true);
-            translate([0, 11, -14]) cylinder(r=R(22), h=4, center=true);
+        translate([0, -34, 25-2-2-10]) {
+            difference () {
+                cube([14, 20, 50], center=true);
+                translate([0, R(LensVoidDiameter)+10+4.01, 0]) cylinder(r=R(LensVoidDiameter)+5, h=LensY + 29, center=true, $fn=200);
+            }
+            translate([0, 11, -14+9]) cylinder(r=R(22), h=4, center=true);
         }
 	}
 }
@@ -178,29 +182,33 @@ module RailMount () {
 
 module OptoEndstopMount () {
         
-        translate([-5,9.5,20]) {
-            
-            difference() {
-                translate([0, 0, 4]) cube([14-0.3-0.3, 14, 32], center=true);
-                translate([0, R(LensVoidDiameter)+15+4, 0]) cylinder(r=R(LensVoidDiameter)+15, h=LensY + 10, center=true, $fn=200);
-                translate([0,-8.3, 12]) cube([9, 8, 5], center=true);
-                //translate([0,-5,-9+OptoEndstopAdjustZ]) rotate([90, 0, 0]) cylinder(r=R(2.9),h=10,center=true, $fn=40);
-                translate([-2,-5,15+OptoEndstopAdjustZ]) rotate([90, 0, 0]) cylinder(r=R(2.9),h=20,center=true, $fn=40);
-                translate([0,1,-3+OptoEndstopAdjustZ]) cube([8,20,15],center=true);
-                //pathway void
-                translate([0,6,-3 +OptoEndstopAdjustZ]) cylinder(r=R(22), h=4, center=true);
+    translate([-5,9.5,20]) {
+        difference() {
+            translate([0, 0, 1-7.25]) cube([14-0.3-0.3, 14, 32+4], center=true);
+            //lens void
+            translate([0, R(LensVoidDiameter)+5+4, 0]) cylinder(r=R(LensVoidDiameter)+5, h=LensY + 29, center=true, $fn=200);
+            //connector void
+            translate([0,-8.3, -14.5]) cube([9, 8, 5], center=true);
+            //bolts
+            translate([2,-5,-13.25+OptoEndstopAdjustZ]) rotate([90, 0, 0]) cylinder(r=R(2.9),h=20,center=true, $fn=40);
+            translate([2,-5,15+OptoEndstopAdjustZ]) rotate([90, 0, 0]) cylinder(r=R(2.9),h=20,center=true, $fn=40);
+            //main void
+            translate([1,1,-3]) cube([8,20,15],center=true);
+            //pathway void
+            translate([0,6,-2]) cylinder(r=R(22), h=4, center=true);
+            //smd voids
+            translate([-5, -6.5, -3]) cube([3.6, 1, 18], center=true);
             }
-            
         }
 }
 
 module Debug () {
     Mount();
-    translate([-CapOffsetX,-CapOffsetY,5.71]) rotate([0,0,currentAngle]) Cap();
+    //translate([-CapOffsetX,-CapOffsetY,5.71]) rotate([0,0,currentAngle]) Cap();
     //color("green") RailMount();
     //translate([5, -38, -11.8+OptoEndstopAdjustZ]) rotate([0, -90, 0]) opto_endstop();
     //color("green") translate([5, -38, -11.8]) OptoEndstopMount();
-    translate([-2, -38 + 2, -11.8 + 20 + OptoEndstopAdjustZ+.75]) rotate([90, 180, 0]) OptoEndstop();
+    //translate([2, -38 + 2, -11.8 + 11 + 2 +.75]) rotate([90, 0, 0]) OptoEndstop();
 }
 
 Render="Debug";