Raspberry Pi-based intervalometer for Bolex 16mm camera https://intval3.sixteenmillimeter.com
Go to file
mmcwilliams 7cc03a2e8d ncu -u && npm i 2019-10-11 17:54:04 -04:00
app Add a favicon before deploying. 2019-06-19 19:32:36 -04:00
conf Move all config files into ./conf 2017-12-31 01:26:29 -05:00
experiments Moved curl script to experiments 2018-02-10 12:09:19 -05:00
hardware Work on anyeye revere projector. 2019-03-26 14:49:47 -04:00
howto Add list of raspi-config commands 2019-03-27 18:46:33 -04:00
lib Compile sequence module as is. 2019-10-11 17:53:41 -04:00
scripts Add a script to configure raspian without raspi-config. This uses the "nonint" command on the raspi-config tool to set individual parameters without launching the entire GUI. 2019-03-26 16:07:56 -04:00
src/sequence Compile sequence module as is. 2019-10-11 17:53:41 -04:00
test Create unit tests for QUnit 2018-02-10 16:34:56 -05:00
.gitignore Ignore .DS_Store 2018-02-12 13:59:32 -05:00
Readme.md Update Readme.md 2019-03-23 11:47:01 -04:00
dev.sh Run node index.js, not the deleted bluetooth service. 2017-11-22 09:31:03 -05:00
docs.sh Install jsdoc-to-markdown for documentation 2017-09-17 15:13:40 -04:00
index.js Reset state and then set newly reset state to web UI 2018-02-12 14:57:06 -05:00
nginx.conf Update nginx config to use static dir 2018-10-07 17:16:22 -04:00
package-lock.json ncu -u && npm i 2019-10-11 17:54:04 -04:00
package.json ncu -u && npm i 2019-10-11 17:54:04 -04:00
process.json BLE features are working, minus the wifi feature. Good work today. 2017-12-13 18:40:14 -05:00

Readme.md

INTVAL3

What is this?

INTVAL3 is an open source intervalometer for the Bolex 16mm camera. The goal of the project is to create a cheap-to-make intervalometer that can be used to automate time-lapse or animation on the Bolex using mobile, web or physical controls.

This is the third incarnation of the INTVAL project, this time utilizing the Raspberry Pi Zero W for Wifi and Bluetooth control. Earlier versions, the INTVAL and INTVAL2 were Arduino-based. The original INTVAL used a solenoid (!!!) to hammer a camera release cable, while the second attempt was a proving ground for the motor-and-key hardware used in this version.

The INTVAL2 project should be used if you prefer a simpler, physical interface approach.

Components

Firmware

The firmware of the INTVAL3 is a node.js application running on the Raspian OS intended for installation on the Raspberry Pi Zero W.

Mobile App

The INTVAL3 mobile app controls the intervalometer over Bluetooth. It can be used to configure the settings on the intervalometer such as exposure length, delay between frames and the direction of the film. The app can also be used to trigger individual frames, as well as start and stop sequences. As an experimental feature, film exposure settings can be determined with the camera on a mobile device.

Web App

As a function of the firmware, there is an embedded web application that is hosted on the INTVAL3. When connected to a wifi network (via the mobile app) users are able to control the intervalometer from a browser. Users are also able to trigger functions and change settings on the intervalometer firmware from the command line by using cURL or wget, so actions can be scripted and automated from an external machine.

Hardware

All of the non-electronic hardware is generated from OpenSCAD scripts and built into either STL files for 3D printing or DXF files for laser cutting or CNCing.

Electronics designs are available in the form of a Fritzing file, Gerber files, a wiring diagram and a mask image that can be used to fabricate a board from a blank PCB.

Prototype of the bare PCB of the "bonnet" for the Raspberry Pi Zero W are available for order from OSH Park. See the parts list below of components for this board.

Order INTVAL3 Bonnet from OSH Park


PARTS

  1. Raspberry Pi Zero W - [Adafruit] [Sparkfun]
  2. L298N Breakout Board - ?
  3. 120RPM 12VDC Motor - ?
  4. Microswitch w/ Roller - [Adafruit]
  5. L7805 5V Regulator - [Adafruit] Sparkfun]
  6. 2x Thru-hole Resistors - 330 Ohm
  7. 1x Thru-hole Capacitor - 10 uF
  8. 1x Thru-hole Capacitor - 100 uF
  9. 4x Terminal blocks