Create repo
This commit is contained in:
mattmcw
commit
cc3dc87564
|
|
@ -0,0 +1,201 @@
|
||||||
|
# axidraw_conf.py
|
||||||
|
# Part of the AxiDraw driver software
|
||||||
|
#
|
||||||
|
# https://github.com/evil-mad/axidraw
|
||||||
|
# Version 2.7.0, dated 2020-11-10.
|
||||||
|
#
|
||||||
|
# Copyright 2020 Windell H. Oskay, Evil Mad Scientist Laboratories
|
||||||
|
#
|
||||||
|
# https://github.com/evil-mad/AxiDraw
|
||||||
|
#
|
||||||
|
# "Change numbers here, not there." :)
|
||||||
|
|
||||||
|
|
||||||
|
'''
|
||||||
|
Primary user-adjustable control parameters:
|
||||||
|
|
||||||
|
We encourage you to freely tune these values as needed to match the
|
||||||
|
behavior and performance of your AxiDraw to your application and taste.
|
||||||
|
|
||||||
|
These parameters are used as defaults when using AxiDraw with the command-
|
||||||
|
line interface (CLI) or with the python library. With the CLI, you can
|
||||||
|
make copies of this configuration file and specify a configuration file.
|
||||||
|
|
||||||
|
If you are operating the AxiDraw from within Inkscape, please set your
|
||||||
|
preferences within Inkscape, using the AxiDraw Control dialog.
|
||||||
|
Most values listed here are ignored when running within Inkscape.
|
||||||
|
|
||||||
|
Similarly, values set within Inkscape are ignored when using the CLI or
|
||||||
|
python library.
|
||||||
|
|
||||||
|
'''
|
||||||
|
|
||||||
|
# DEFAULT VALUES
|
||||||
|
|
||||||
|
speed_pendown = 25 # Maximum plotting speed, when pen is down (1-100)
|
||||||
|
speed_penup = 75 # Maximum transit speed, when pen is up (1-100)
|
||||||
|
accel = 75 # Acceleration rate factor (1-100)
|
||||||
|
|
||||||
|
pen_pos_up = 60 # Height of pen when raised (0-100)
|
||||||
|
pen_pos_down = 30 # Height of pen when lowered (0-100)
|
||||||
|
|
||||||
|
pen_rate_raise = 75 # Rate of raising pen (1-100)
|
||||||
|
pen_rate_lower = 50 # Rate of lowering pen (1-100)
|
||||||
|
|
||||||
|
pen_delay_up = 0 # Optional delay after pen is raised (ms)
|
||||||
|
pen_delay_down = 0 # Optional delay after pen is lowered (ms)
|
||||||
|
|
||||||
|
const_speed = False # Use constant velocity mode when pen is down.
|
||||||
|
report_time = False # Report time elapsed.
|
||||||
|
default_layer = 1 # Layer(s) selected for layers mode (1-1000).
|
||||||
|
|
||||||
|
copies = 1 # Copies to plot, or 0 for continuous plotting. Default: 1
|
||||||
|
page_delay = 15 # Optional delay between copies (s).
|
||||||
|
|
||||||
|
preview = False # Preview mode; simulate plotting only.
|
||||||
|
rendering = 3 # Preview mode rendering option (0-3):
|
||||||
|
# 0: Do not render previews
|
||||||
|
# 1: Render only pen-down movement
|
||||||
|
# 2: Render only pen-up movement
|
||||||
|
# 3: Render all movement (Default)
|
||||||
|
|
||||||
|
model = 1 # AxiDraw Model (1-4).
|
||||||
|
# 1: AxiDraw V2 or V3 (Default).
|
||||||
|
# 2: AxiDraw V3/A3 or SE/A3.
|
||||||
|
# 3: AxiDraw V3 XLX.
|
||||||
|
# 4: AxiDraw MiniKit.
|
||||||
|
|
||||||
|
port = None # Serial port or named AxiDraw to use.
|
||||||
|
# None (Default) will plot to first unit located.
|
||||||
|
|
||||||
|
port_config = 0 # Serial port behavior option (0-2)
|
||||||
|
# 0: Plot to first unit found, unless port is specified (Default),
|
||||||
|
# 1: Plot to first AxiDraw unit located
|
||||||
|
# 2: Plot to a specific AxiDraw only, given by port.
|
||||||
|
|
||||||
|
auto_rotate = True # Auto-select portrait vs landscape orientation
|
||||||
|
# Default: True
|
||||||
|
|
||||||
|
reordering = 0 # Plot optimization option for how groups are handled
|
||||||
|
# 0: Preserve order of objects given in SVG file (Default).
|
||||||
|
# 1: Reorder objects, preserving groups
|
||||||
|
# 2: Reorder objects, reordering within each group
|
||||||
|
# 3: Reorder all objects, breaking apart groups
|
||||||
|
|
||||||
|
resolution = 1 # Resolution: (1-2):
|
||||||
|
# 1: High resolution (smoother, slightly slower) (Default)
|
||||||
|
# 2: Low resolution (coarser, slightly faster)
|
||||||
|
|
||||||
|
'''
|
||||||
|
Additional user-adjustable control parameters:
|
||||||
|
|
||||||
|
Values below this point are configured only in this file, not through the user interface(s).
|
||||||
|
'''
|
||||||
|
|
||||||
|
servo_timeout = 60000 # Time, ms, for servo motor to power down
|
||||||
|
# after last movement command (default: 60000)
|
||||||
|
# This feature requires EBB v 2.5 hardware (with USB
|
||||||
|
# micro not USB mini connector) and firmware version
|
||||||
|
# 2.6.0 or newer
|
||||||
|
|
||||||
|
check_updates = True # If True, allow AxiDraw Control to check online to see
|
||||||
|
# what the current software version is, when you
|
||||||
|
# query the version. Set to False to disable. Note that
|
||||||
|
# this is the only internet-enabled function in the
|
||||||
|
# AxiDraw software.
|
||||||
|
|
||||||
|
smoothness = 10.0 # Curve smoothing (default: 10.0)
|
||||||
|
|
||||||
|
cornering = 10.0 # Cornering speed factor (default: 10.0)
|
||||||
|
|
||||||
|
use_b3_out = False # If True, enable digital output pin B3, which will be high (3.3V)
|
||||||
|
# when the pen is down, and low otherwise. Can be used to control
|
||||||
|
# external devices like valves, relays, or lasers.
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
# Effective motor resolution is approx. 1437 or 2874 steps per inch, in the two modes respectively.
|
||||||
|
# Note that these resolutions are defined along the native axes of the machine (X+Y) and (X-Y),
|
||||||
|
# not along the XY axes of the machine. This parameter chooses 8X or 16X microstepping on the motors.
|
||||||
|
|
||||||
|
|
||||||
|
'''
|
||||||
|
Secondary control parameters:
|
||||||
|
|
||||||
|
Values below this point are configured only in this file, not through the user interface(s).
|
||||||
|
Please note that these values have been carefully chosen, and generally do not need to be
|
||||||
|
adjusted in everyday use. That said, proceed with caution, and keep a backup copy.
|
||||||
|
'''
|
||||||
|
|
||||||
|
# Page size values typically do not need to be changed. They primarily affect viewpoint and centering.
|
||||||
|
# Measured in page pixelssteps. Default printable area for AxiDraw is 300 x 218 mm
|
||||||
|
|
||||||
|
x_travel_default = 11.81 # AxiDraw V2 and AxiDraw V3: X Carriage travel in inches. Default: 300 mm = about 11.81 inches
|
||||||
|
y_travel_default = 8.58 # AxiDraw V2 and AxiDraw V3: Y Carriage travel in inches. Default: 218 mm = about 8.58 inches
|
||||||
|
|
||||||
|
x_travel_V3A3 = 16.93 # AxiDraw V3/A3: X Carriage travel in inches. Default: 430 mm = about 16.93 inches
|
||||||
|
y_travel_V3A3 = 11.69 # AxiDraw V3/A3: Y Carriage travel in inches. Default: 297 mm = about 11.69 inches
|
||||||
|
|
||||||
|
x_travel_V3XLX = 23.42 # AxiDraw V3 XLX: X Carriage travel in inches. Default: 595 mm = about 23.42 inches
|
||||||
|
y_travel_V3XLX = 8.58 # AxiDraw V3 XLX: Y Carriage travel in inches. Default: 218 mm = about 8.58 inches
|
||||||
|
|
||||||
|
x_travel_MiniKit = 6.30 # AxiDraw MiniKit: X Carriage travel in inches. Default: 160 mm = about 6.30 inches
|
||||||
|
y_travel_MiniKit = 4.00 # AxiDraw MiniKit: Y Carriage travel in inches. Default: 101.6 mm = 4.00 inches
|
||||||
|
|
||||||
|
|
||||||
|
#native_res_factor = 1016.0 # Motor resolution calculation factor, steps per inch, and used in conversions. Default: 1016.0
|
||||||
|
native_res_factor = 1275.0
|
||||||
|
# Note that resolution is defined along native (not X or Y) axes.
|
||||||
|
# Resolution is native_res_factor * sqrt(2) steps per inch in Low Resolution (Approx 1437 steps per inch)
|
||||||
|
# and 2 * native_res_factor * sqrt(2) steps per inch in High Resolution (Approx 2874 steps per inch)
|
||||||
|
|
||||||
|
max_step_rate = 24.995 # Maximum allowed motor step rate, in steps per millisecond.
|
||||||
|
# Note that 25 kHz is the absolute maximum step rate for the EBB.
|
||||||
|
# Movement commands faster than this are ignored; may result in a crash (loss of position control).
|
||||||
|
# We use a conservative value, to help prevent errors due to rounding.
|
||||||
|
# This value is normally used _for speed limit checking only_.
|
||||||
|
|
||||||
|
speed_lim_xy_lr = 15.000 # Maximum XY speed allowed when in Low Resolution mode, in inches per second. Default: 15.000 Max: 17.3958
|
||||||
|
speed_lim_xy_hr = 8.6979 # Maximum XY speed allowed when in High Resolution mode, in inches per second. Default: 8.6979, Max: 8.6979
|
||||||
|
# Do not increase these values above Max; they are derived from max_step_rate and the resolution.
|
||||||
|
|
||||||
|
max_step_dist_lr = 0.000696 # Maximum distance covered by 1 step in Low Res mode, rounded up, in inches. ~1/(1016 sqrt(2))
|
||||||
|
max_step_dist_hr = 0.000348 # Maximum distance covered by 1 step in Hi Res mode, rounded up, in inches. ~1/(2032 sqrt(2))
|
||||||
|
# In planning trajectories, we skip movements shorter than these distances, likely to be < 1 step.
|
||||||
|
|
||||||
|
const_speed_factor_lr = 0.25 # When in constant-speed mode, multiply the pen-down speed by this factor. Default: 0.25 for Low Res mode
|
||||||
|
const_speed_factor_hr = 0.4 # When in constant-speed mode, multiply the pen-down speed by this factor. Default: 0.4 for Hi Res mode
|
||||||
|
|
||||||
|
start_pos_x = 0 # Parking position, inches. Default: 0
|
||||||
|
start_pos_y = 0 # Parking position, inches. Default: 0
|
||||||
|
|
||||||
|
# Acceleration & Deceleration rates:
|
||||||
|
accel_rate = 40.0 # Standard acceleration rate, inches per second squared
|
||||||
|
accel_rate_pu = 60.0 # Pen-up acceleration rate, inches per second squared
|
||||||
|
|
||||||
|
time_slice = 0.025 # Interval, in seconds, of when to update the motors. Default: time_slice = 0.025 (25 ms)
|
||||||
|
|
||||||
|
bounds_tolerance = 0.003 # Suppress warnings if bounds are exceeded by less than this distance (inches).
|
||||||
|
|
||||||
|
# Allow sufficiently short pen-up moves to be substituted with a pen-down move:
|
||||||
|
min_gap = 0.008 # Distance Threshold (inches). Default value: 0.008 inches; smaller than most pen lines.
|
||||||
|
|
||||||
|
# Servo motion limits, in units of (1/12 MHz), about 83 ns:
|
||||||
|
servo_max = 27831 # Highest allowed position; "100%" on the scale. Default value: 25200 units, or 2.31 ms.
|
||||||
|
servo_min = 9855 # Lowest allowed position; "0%" on the scale. Default value: 10800 units, or 0.818 ms.
|
||||||
|
|
||||||
|
# Note that previous versions of this configuration file used a wider range, 7500 - 28000, corresponding to a range of 625 us - 2333 us.
|
||||||
|
# The new limiting values are equivalent to 16%, 86% on that prior scale, giving a little less vertical range, but higher resolution.
|
||||||
|
# More importantly, it constrains the servo to within the travel ranges that they are typically calibrated, following best practice.
|
||||||
|
|
||||||
|
skip_voltage_check = False # Set to True if you would like to disable EBB input power voltage checks. Default: False
|
||||||
|
|
||||||
|
clip_to_page = True # Clip plotting area to SVG document size. Default: True
|
||||||
|
|
||||||
|
# the tolerance for determining when the bezier has been segmented enough to plot:
|
||||||
|
bezier_segmentation_tolerance = 0.02 / smoothness
|
||||||
|
|
||||||
|
# Tolerance for determining which segments can be merged:
|
||||||
|
# Larger values of segment_supersample_tolerance
|
||||||
|
# give smoother plotting along paths that began with too many vertices.
|
||||||
|
segment_supersample_tolerance = bezier_segmentation_tolerance / 16
|
||||||
|
|
@ -0,0 +1,14 @@
|
||||||
|
A3 11-3/4" x 16-1/2" 297 x 420 mm
|
||||||
|
A4 8-1/4" x 11-3/4" 210 x 297 mm
|
||||||
|
8x10 8" x 10" 203 x 254 mm
|
||||||
|
|
||||||
|
|
||||||
|
dot pixels calculation
|
||||||
|
|
||||||
|
W=format.w/pen_size
|
||||||
|
H=format.h/pen_size
|
||||||
|
|
||||||
|
so
|
||||||
|
|
||||||
|
W= 203/0.3 = 676
|
||||||
|
H= 254/0.3 = 846
|
||||||
|
|
@ -0,0 +1,5 @@
|
||||||
|
#!/bin/bash
|
||||||
|
|
||||||
|
# bash threshold.sh input value output
|
||||||
|
|
||||||
|
convert "${1}" -monochrome -white-threshold ${2} +matte -colors 4 -depth 2 "${3}"
|
||||||
Loading…
Reference in New Issue